UPVC Window Handle Replacement

Replacing a broken window handle is a easy process, and, with the right tools, it can be done quickly. It is essential to identify the kind of handle you have and its spindle size before purchasing a replacement.

Older uPVC window handles have a spur that extends and is locked over the wedge striker for cockspur. These can be either right or left-handed and have to be matched when replacing.

What kind of lock and handle do I have?

There are many window locks and handles made from upvc each with its own advantages and purposes. The type of handle you have will determine if the locking mechanism you have is effective and if it's easy to open the windows replacement glass. With time and regular use, the upvc handles on your windows can be damaged and worn out. This makes them less secure and effective. In some instances, they could even fall completely off. If you find that your window handles have fallen off, it is crucial to repair them as quickly as possible. This will stop potential burglaries and keep your home safe.

It is a good thing that replacing your window handles made of upvc is a fairly simple job that can be completed by everyone. You'll need some basic tools, but with the proper knowledge, it's a straightforward process that should only take a couple of minutes. You will need to know the type of handle or lock that you have on your window. This will help you select the right replacement window seals.

Inline Espagnolette Handles

They are typically found on the outside of the window. They are flat and have a latch which engages the locking mechanism of the window frame. Inline upvc handles also come with a spindle that goes through the middle of the handle and then into the window frame to operate the latch.

Cockspur Handles

They are typically found on older uPVC window frames and have a distinctive, hook-shaped design. Cockspur handles are held to the frame of the window by one screw, and are less secure than other types of window handles.

Handles that can tilt and turn

The tilt and turn handles differ from other upvc handles in that they can be turned for opening the window, and then tilted into the window to ventilate. They feature a 7mm spindle on the back and are available both in right-hand and left-hand versions.

When buying replacement sash windows upvc handles it is essential to verify the length of the spindle as not all are identical in size. Drop something in the middle of the hole to measure the length. This is the maximum size of spindle that will fit into your windows.

What is the spindle?

uPVC window handles function similarly as doors. By turning the handle, you will be able to activate a latch inside the frame. The window then opens and closed. However, sometimes handles can be damaged, particularly when they are used frequently or exposed to extreme weather conditions. This could mean that you have to replace your uPVC handles for windows as they might not be able to operate the window correctly in the future.

There are many different kinds of uPVC handles that are available, including Espag, Cockspur and Spaded handle options. They are designed to fit inside the uPVC frames in various ways, and each type of handle has a particular spindle that is used to lock the mechanism to the window. It is crucial to know the type of handle you have installed on your uPVC windows to ensure that you replace it with the correct one.

The base of the handle will inform the type of uPVC it is. A snap-in cover is over the screw that holds the base of the handle in position. Remove this and then you should be able to see the second holding screw at the opposite end of the base of the handle. Once both screws have been removed then you should be able to remove the handle from the uPVC.

After you have removed the uPVC window handle, you will need to carefully unscrew the old spindle from the locking mechanism. Note the length of the spindle. You'll need purchase a replacement with the same length as the handle that was originally used and the locking device.

The spindle wears down and cannot operate the locking mechanism. This can be due to wear and tear from continuous use or a loosening of the locking mechanism, or even rust over time. When this happens it is necessary to replace the window handle as well as the locking mechanism to restore complete functionality to your uPVC windows.

How do I remove the old handle?

Window handles can become damaged or even broken over the course cost of windows replacement time. It is crucial to repair them as quickly a possible to ensure your security. It is simple to replace a worn or damaged handle. The job can be completed in under a minute without the need of special tools.

To take off the handle, first remove the screw located at the base of the handle. After this screw is removed, the handle will be pulled away from the base. A second screw is located at the base of the handle. This can also be removed. After the two screws are removed, the handle can be detached from the window's base.

After the handle has been removed, take the new handle and line up the fixing holes with the holes present in the window frame. There may be a little sticker or caps on the new handle, so remove the caps if needed, and then put the handle in place. Once the handle is set, it is essential to check that it is working by turning the handle and making sure that the lock mechanism is activated.

Espag handles have an extra spindle that is protruding from the handle and slot into a multipoint locking mechanism inside the frame of the window. Cadenza windows have an edge with cut-outs which slot into the lock mechanism while Cockspur handles have a long nose that hooks over either the frame's outer or transom bar cross-member within the window.

Once you have the new handle in place, slide the spindle into the lock inside the window and then tighten it. Replace the snap-in cover and screw cap (if appropriate) after the handle is fixed. Once the handle is in use, open and close the window a few times to make sure it is working properly and securely.

How do I install the new handle?

It's not difficult to change the handle on your Upvc windows. The process is very simple. You only need a screwdriver and a bit of patience. The first step is to ensure that the handle is not locked and then take out any screws that are visible, you can also replace these by screw caps if you need. After removing the handle you'll need to take note of the length of the spindle which extends from the back. This is vital as it will determine what kind of handle you will need to purchase.

Espagnolette handles on uPVC are the most sought-after kind of handle. They feature a spindle that is connected to the handle, and is responsible for an internal locking mechanism within the window frame. When the handle is turned it opens the latch on the window, allowing it to open. In regular use and time, handles for espagnolette may become damaged.

Cadenza handles are a form of uPVC handle that is typically used in tilt and turn windows. They have an extended blade that works a multipoint locking mechanism within the window. They are more secure than espagnolette handles since they only open from the inside. You can replace them using the same method that you would with espagnolette handles, but make sure the new handle is angled and not flat.

Once you've decided on the right handle to purchase You can simply line up the new handle with the existing screw holes and then screw it in place. Then, put the screws on and test the new handle. You can perform this by moving the handle between the locked position to the unlocked a few time. It might be worthwhile to speak with an expert to determine how you can fix any problems. They can advise you on how to solve the problem in a timely and efficient way.