Double Glazing Door Lock repairs to double glazing windows

Is your uPVC window or door mechanism broken? Perhaps the handles on your uPVC windows and doors are not aligned properly or are difficult to use.

It is crucial that your double glazing windows repairs-glazed doors work smoothly, otherwise you'll lose energy and increase the chance of burglary. Owen the Locksmith can fix your door lock at an affordable price.

Snapped Key

If a key is snapped off within the lock, it can be incredibly annoying. It could also be a security risk because it could leave you vulnerable to burglars if your door does not lock. Fortunately, there are simple fixes you can use to solve the issue and get your door working properly again.

Keep calm. If you get scared and start poking around wildly you may end up pushing the damaged piece of the key further into the lock, thereby making the situation worse.

Then spray WD-40 or another penetrating oil into the lock to make the broken piece slide out more easily. You can also make use of a screwdriver repairs to double glazing windows break up any pieces stuck that could be hindering the flow. If you're lucky enough to have a small piece of the key that is visible it, you can make use of a paperclip, or any other thin metal object to grab it and remove it. Both methods work, but be careful not to push the broken key further into the keyway.

Some paperclips have grooved edges that can be used as hook extractors. Jigsaw blades are also well for this. If you don't have one of these tools then you can bend a hook using needle-nosed pliers. Finally, you can use a pair of tweezers grasp and pull out the last piece of broken keys.

If you're unable to pull the broken piece of the key out, you can try using a lock de-icer. It's available at most hardware stores and works by freezing any moisture that may be present within the lock.

If none of these tricks are working then it's probably time to call in locksmith. Fitlocks specialists are able to quickly resolve issues with uPVC door mechanisms and locks, including snapped keys and broken handles. They can also alter your double glazing door mechanisms to make them more user-friendly. You can book an appointment online for a double-glazing repair or contact us to discuss your needs.

Broken Cylinder

A broken cylinder is an extremely risky security issue. It's a good thing that it's a simple repair for an expert locksmith to complete. To fix the cylinder, locksmiths must tap it. This can be done using a hammer, or any other tool. The best method is to employ a wire or long match. Position the match or the wire's end in the keyway. After this, the locksmith can hit the lock to break it open. This is much better than using a heavy hammer, which could harm the lock.

Overheating is the primary reason behind cylinder heads cracking. This can happen when the cylinder block and head are made from different metals, like cast iron and aluminium. When various metals heat up and cool down at different rates, it can cause localised hotspots that expand faster than the rest of the head of the cylinder, leading to cracks.

Corrosion is another possible cause of cracks in the cylinder. When the cylinder head and the cylinder block aren't maintained properly, this could cause corrosion or rust and cause them to expand at a higher rate than they ought to. Over time, this can cause cracks.

If your uPVC window lock or door is brittle or requires an enormous amount of pressure to turn, this can be caused by many things. A malfunctioning locking mechanism, misalignment or an old handle are the most common reasons for this issue.

Fortunately, this is an easy and affordable fix for the majority of homeowners of Double glazed window Repairs near me glazing. A professional locksmith should be able to solve this issue within a matter of hours of arriving at your home. They can replace the locking mechanisms, or replace the window handles, and also change the gearboxes based on your specific needs. A professional locksmith can always advise you on the most cost-effective options for your home. They can also suggest upgrades to high-security 3 Star TS007 euro cylinders that will give you an additional layer of security against burglars. It's a small price to enjoy the peace of mind that comes from knowing your uPVC door is secured.

Broken Handle

It's not a surprise that window handle locks may break. They have complex mechanisms that wear out over time. It isn't always easy to pinpoint the reason for a broken window handle lock and repair double glazing it correctly.

Fixing your broken handle, whether it's an internal latch or the locking mechanism will increase the security of your uPVC door and stop draughts. It could be costly to replace or repair your handle incorrectly and it can also harm the frame and the lock of your door.

Screwdriver When the window is open, loosen the screw holding the handle. The screw should be on the inside of the back plate, normally concealed by a screw cover for aesthetic reasons. Be sure to not damage any of the internal components within the handle, for example the plates or levers that are on either side of the spindle. Ideally, keep them in the same order so you can re-install them in the event of a need.

Next, turn the handle to make it 90 degrees to the window frame and loosen the screw at the back of the handle which holds it to the internal spindle by using a second screwdriver. Once the screw is loose, you can remove the handle and remove the broken spindle. Replace this with a new one, ensuring it's the same length as the old one (you will typically find them online or in hardware stores) and then securely screw it in the correct position. Don't over tighten the screw as this could harm the handle as well as the window frame.

Close the handle and try it. It should function smoothly, and you will be able open your window once again.

Don't forget to double-check that your uPVC window is closing properly when you're working with the handle. If they aren't closing properly, you may experience draughts or damp in your home. Also, you could be compromising the energy efficiency of your home. A local window company, such as Core Sash Windows, will be capable of adjusting the hinges on your window frames to ensure they are able to shut properly.

Broken Spindle

It is often the case that the spindle inside the handle breaks, rather than the handle itself. This is particularly frequent in uPVC tilt and turn windows. These kinds of windows require a handle which is a lock mechanism that is located in the frame of the window. The handle is attached to a central rod which in turn activates cams that resemble mushrooms, which locks are inserted into the window frame. If the dead latch mechanism does not open when the handle is turned it is likely that the spindle has broken and this could be a frustrating problem.

There are solutions to this issue. A good locksmith can quickly and efficiently fix this problem. They can disassemble the window handle by using a tool that removes the wheel portion of the mechanism where the spindle is. This is done without damage to the handle or window frame.

Once the wheel is removed the technician can then inspect the spindle and determine what has caused it to break. This involves breaking down the spindle into its constituent parts and meticulously noting their general condition, as well as any specific areas of damage or excessive wear. This process is usually carried out by technicians in a clean and safe environment.

The next step is to clean the damaged spindle, this helps eliminate any debris or dirt that could be hindering its normal function. The spindle may be replaced or repaired. If it's being replaced, the technician will need a dowel of a similar size to the original and drill mating holes into both pieces of the spindle. This will ensure that the new spindle is a precise fit with the handle.

If the damaged spindle cannot be repaired, it could require replacement completely. Home centres sell generic substitutes however if your window design is unusual you'll have to speak with an expert in cabinet making or woodworking who can replicate the exact part. After the spindle is installed, it is fixed to the handle. Place the screw holes on the handle with the screws already in the frame. Once the new handle is firmly installed, you are now ready to operate your uPVC window.